mirror of
https://github.com/laanwj/k210-sdk-stuff.git
synced 2024-11-22 17:36:20 +04:00
708 lines
42 KiB
Markdown
708 lines
42 KiB
Markdown
Kendryte K210 memory map
|
||
------------------------
|
||
|
||
This is a rough memory map for the Kendryte K210 (as used on the Sipeed Maix boards). For some reason this is missing from the [data sheet](https://s3.cn-north-1.amazonaws.com.cn/dl.kendryte.com/documents/kendryte_datasheet_20181011163248_en.pdf). I've tried to use the same naming when possible.
|
||
|
||
from to description
|
||
---------- ---------- ---------------------------------------
|
||
0x00000000 0x0fffffff CorePlex
|
||
0x00000000 0x00000fff DEBUG
|
||
0x00001000 0x00001fff ROMCPU
|
||
0x02000000 0x03ffffff CLINT
|
||
0x0c000000 0x0fffffff PLIC
|
||
0x38000000 0x3fffffff TileLink
|
||
0x38000000 UARTHS
|
||
0x38001000 GPIOHS
|
||
0x40000000 0x4fffffff AXI 64-bit (non-cached)
|
||
0x40000000 0x403fffff General-purpose SRAM MEM0 (non-cached)
|
||
0x40400000 0x405fffff General-purpose SRAM MEM1 (non-cached)
|
||
0x40600000 0x407fffff AI SRAM (non-cached)
|
||
0x40800000 KPU
|
||
0x42000000 0x423fffff FFT
|
||
0x50000000 0x501fffff AHB 32-bit
|
||
0x50000000 DMAC
|
||
0x50200000 0x503fffff APB1 32 bit
|
||
0x50200000 GPIO
|
||
0x50210000 UART1
|
||
0x50220000 UART2
|
||
0x50230000 UART3
|
||
0x50240000 SPI2
|
||
0x50250000 I2S0
|
||
0x50250200 APU
|
||
0x50260000 I2S1
|
||
0x50270000 I2S2
|
||
0x50280000 I2C0
|
||
0x50290000 I2C1
|
||
0x502a0000 I2C2
|
||
0x502b0000 FPIOA
|
||
0x502c0000 SHA256
|
||
0x502d0000 TIMER0
|
||
0x502e0000 TIMER1
|
||
0x502f0000 TIMER2
|
||
0x50400000 0x505fffff APB2 32 bit
|
||
0x50400000 WDT0
|
||
0x50410000 WDT1
|
||
0x50420000 OTP
|
||
0x50430000 DVP
|
||
0x50440000 SYSCTL
|
||
0x50450000 AES
|
||
0x50460000 RTC
|
||
0x52000000 0x5??????? APB3 32 bit
|
||
0x52000000 SPI0
|
||
0x53000000 SPI1
|
||
0x54000000 SPI3
|
||
0x80000000 0x8fffffff AXI 64-bit (cached mirror of 0x40000000)
|
||
0x80000000 0x803fffff General-purpose SRAM MEM0 (cached)
|
||
0x80400000 0x805fffff General-purpose SRAM MEM1 (cached)
|
||
0x80600000 0x807fffff AI SRAM (cached)
|
||
0x88000000 0x8801ffff ROM
|
||
|
||
Source (paths refer to Kendryte stand-alone SDK):
|
||
- `lib/bsp/include/platform.h`
|
||
- `lib/drivers/apu.c`
|
||
- ROM dump (there's a compiled device tree in there)
|
||
|
||
RAM ranges
|
||
-----------
|
||
|
||
- The 2MB of AI SRAM at `0x80600000` can be used as normal RAM when the KPU is not used.
|
||
|
||
- The `0x4xxxxxxx` range has a non-cached mirror of the SRAMs. Interestingly, floating point load instructions [don't work](https://github.com/rust-embedded/riscv-rt/issues/25#issuecomment-491524341) from this area.
|
||
|
||
- There is a mirror of the cached SRAM area at `0xffffffff80000000`, this is useful for the [medlow memory model](https://www.sifive.com/blog/all-aboard-part-4-risc-v-code-models).
|
||
|
||
- More generally, it looks like the upper 32 bits of the address are ignored.
|
||
|
||
Boot sequence
|
||
-------------
|
||
|
||
`ROMCPU` (`0x00001000`) seems to be the initial boot vector, from there, there's a jump to the beginning of the main ROM (`0x88000000`). This ROM implements loading of the flash to memory at `0x80000000` and jumping to it, as well as "ISP" mode for directly uploading a program from the serial port (this is used by `kflash.py` for flashing).
|
||
|
||
### ISP mode
|
||
|
||
From the datasheet:
|
||
|
||
> IO_16 is used for boot mode selection. During power-on reset, pull high to bootfrom FLASH and pull low to enter ISP mode. After reset, IO_0, IO_1, IO_2, and IO_3 are JTAG pins. IO_4 and IO_5 are ISP pins
|
||
|
||
A packet-based protocol over serial (at baudrate 115200) is used to communicate with the device. The following commands are documented to exist in ISP mode (source: `kflash.py`):
|
||
|
||
0xC1 ECHO (not implemented, returns INVALID_COMMAND)
|
||
0xC2 NOP
|
||
0xC3 MEMORY_WRITE
|
||
0xC4 MEMORY_READ (not implemented, returns INVALID_COMMAND)
|
||
0xC5 MEMORY_BOOT
|
||
0xC6 UARTHS_BAUDRATE_SET
|
||
|
||
Packets are encoded in so-called SLIP format. This means `0xc0` is used as packet beginning and end marker, the escape sequence `0xdb 0xdc` is used to encode `0xc0`, and `0xdb 0xdd` encodes `0xdb`. The first byte of a packet is the command or response code.
|
||
|
||
The following responses can be returned:
|
||
|
||
0xE0 OK
|
||
0xE1 BAD_DATA_LEN
|
||
0xE2 BAD_DATA_CHECKSUM
|
||
0xE3 INVALID_COMMAND
|
||
|
||
- Setting the baud rate in the ISP to anything besides 115200 with `UARTHS_BAUDRATE_SET` doesn't work reliably.
|
||
According to Kendryte trying to do so is [dinosaur-infested](https://github.com/kendryte/kflash.py/blob/master/kflash.py#L513),
|
||
which means the higher baudrate used there (1500000) only works with some boards.
|
||
|
||
IO maps for devices
|
||
===================
|
||
|
||
Registers are 32-bit unless mentioned otherwise.
|
||
|
||
AES
|
||
---
|
||
|
||
(source: `lib/drivers/include/aes.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `aes_key[4]` | customer key.1st~4th byte key |
|
||
| 0x10 | `encrypt_sel` | 0: encryption; 1: decryption |
|
||
| 0x14 | `mode_ctl` | aes mode reg |
|
||
| 0x18 | `aes_iv[4]` | Initialisation Vector. GCM support 96bit. CBC support 128bit |
|
||
| 0x28 | `aes_endian` | input data endian;1:little endian; 0:big endian |
|
||
| 0x2c | `aes_finish` | calculate status. 1:finish; 0:not finish |
|
||
| 0x30 | `dma_sel` | aes out data to dma 0:cpu 1:dma |
|
||
| 0x34 | `gb_aad_num` | gcm Additional authenticated data number |
|
||
| 0x38 | reserved | |
|
||
| 0x3c | `gb_pc_num` | aes plantext/ciphter text input data number |
|
||
| 0x40 | `aes_text_data` | aes plantext/ciphter text input data |
|
||
| 0x44 | `aes_aad_data` | Additional authenticated data |
|
||
| 0x48 | `tag_chk` | [1:0],b'00:check not finish; b'01:check fail; b'10:check success; b'11:reversed |
|
||
| 0x4c | `data_in_flag` | data can input flag. 1: data can input; 0 : data cannot input |
|
||
| 0x50 | `gcm_in_tag[4]` | gcm input tag for compare with the calculate tag |
|
||
| 0x60 | `aes_out_data` | aes plantext/ciphter text output data |
|
||
| 0x64 | `gb_aes_en` | aes module enable |
|
||
| 0x68 | `data_out_flag` | data can output flag 1: data ready 0: data not ready |
|
||
| 0x6c | `tag_in_flag` | allow tag input when use gcm |
|
||
| 0x70 | `tag_clear` | clear `tag_chk` |
|
||
| 0x74 | `gcm_out_tag[4]` | gcm tag output |
|
||
| 0x84 | `aes_key_ext[4]` | customer key for aes-192 aes-256.5th~8th byte key |
|
||
|
||
APU
|
||
---
|
||
|
||
(source: `lib/drivers/include/apu.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ---------------------- | ------------------------------------------------------------- |
|
||
| 0x000 | `bf_ch_cfg_reg` | Channel Config Register |
|
||
| 0x004 | `bf_ctl_reg` | Control Register |
|
||
| 0x008 | `bf_dir_bidx[16][2]` | Direction Sample Buffer Read Index Configure Register |
|
||
| 0x088 | `bf_pre_fir0_coef[9]` | FIR0 pre-filter coefficients |
|
||
| 0x0ac | `bf_post_fir0_coef[9]` | FIR0 post-filter coefficients |
|
||
| 0x0d0 | `bf_pre_fir1_coef[9]` | FIR1 pre-filter coeffecients |
|
||
| 0x0f4 | `bf_post_fir1_coef[9]` | FIR1 post-filter coefficients |
|
||
| 0x118 | `bf_dwsz_cfg_reg` | Downsize Config Register |
|
||
| 0x11c | `bf_fft_cfg_reg` | FFT Config Register |
|
||
| 0x120 | `sobuf_dma_rdata` | Read register for DMA to sample-out buffers |
|
||
| 0x124 | `vobuf_dma_rdata` | Read register for DMA to voice-out buffers |
|
||
| 0x128 | `bf_int_stat_reg` | Interrupt Status Register |
|
||
| 0x12c | `bf_int_mask_reg` | Interrupt Mask Register |
|
||
| 0x130 | `saturation_counter` | Saturation Counter |
|
||
| 0x134 | `saturation_limits` | Saturation Limits |
|
||
|
||
CLINT
|
||
-----
|
||
|
||
(source: `lib/drivers/include/clint.h`, addresses are absolute)
|
||
|
||
| Address | Description |
|
||
|------------|---------------------------------|
|
||
| 0x02000000 | `msip` for core 0 |
|
||
| 0x02000004 | `msip` for core 1 |
|
||
| ... | ... |
|
||
| 0x02003ff8 | `msip` for core 4094 |
|
||
| | |
|
||
| 0x02004000 | `mtimecmp` for core 0 |
|
||
| 0x02004008 | `mtimecmp` for core 1 |
|
||
| ... | ... |
|
||
| 0x0200bff0 | `mtimecmp` For core 4094 |
|
||
| 0x0200bff8 | `mtime` |
|
||
| | |
|
||
| 0x0200c000 | Reserved |
|
||
| ... | ... |
|
||
| 0x0200effc | Reserved |
|
||
|
||
This looks similar to, or even the same as, the SiFive CLINT.
|
||
|
||
DEBUG
|
||
-----
|
||
|
||
Likely follows the [RISC-V debug spec](https://github.com/riscv/riscv-debug-spec/blob/release/riscv-debug-release.pdf)
|
||
and is only accessible from debug mode through JTAG.
|
||
|
||
DMAC
|
||
----
|
||
|
||
(source: `lib/drivers/include/dmac.h`)
|
||
|
||
Registers are 64 bit.
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x000 | `id` | DMAC ID Rgister |
|
||
| 0x008 | `compver` | DMAC COMPVER Register |
|
||
| 0x010 | `cfg` | DMAC Configure Register |
|
||
| 0x018 | `chen` | Channel Enable Register |
|
||
| 0x020 | `reserved[2]` | |
|
||
| 0x030 | `intstatus` | DMAC Interrupt Status Register |
|
||
| 0x038 | `com_intclear` | DMAC Common register Interrupt Status Register |
|
||
| 0x040 | `com_intstatus_en` | DMAC Common Interrupt Enable Register |
|
||
| 0x048 | `com_intsignal_en` | DMAC Common Interrupt Signal Enable Register |
|
||
| 0x050 | `com_intstatus` | DMAC Common Interrupt Status |
|
||
| 0x058 | `reset` | DMAC Reset register |
|
||
| 0x060 | `reserved[20]` | |
|
||
| 0x100 | `channel[6]` | DMA channels configuration |
|
||
|
||
DVP
|
||
---
|
||
|
||
(source: `lib/drivers/include/dvp.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ----------------------------------- |
|
||
| 0x00 | `dvp_cfg` | Config Register |
|
||
| 0x04 | `r_addr` | Output address for red component |
|
||
| 0x08 | `g_addr` | Output address for green component |
|
||
| 0x0c | `b_addr` | Output address for blue component |
|
||
| 0x10 | `cmos_cfg` | CMOS Config Register |
|
||
| 0x14 | `sccb_cfg` | SCCB Config Register |
|
||
| 0x18 | `sccb_ctl` | SCCB Control Register |
|
||
| 0x1c | `axi` | AXI Register |
|
||
| 0x20 | `sts` | STS Register |
|
||
| 0x24 | `reverse` | |
|
||
| 0x28 | `rgb_addr` | Output address for R5G6B5 data |
|
||
|
||
FFT
|
||
---
|
||
|
||
(source: `lib/drivers/include/fft.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ----------------------------------- |
|
||
| 0x00 | `fft_input_fifo` | Input data FIFO |
|
||
| 0x08 | `fft_ctrl` | FFT ctrl reg |
|
||
| 0x10 | `fifo_ctrl` | FIFO ctrl |
|
||
| 0x18 | `intr_mask` | Interrupt mask |
|
||
| 0x20 | `intr_clear` | Interrupt clear |
|
||
| 0x28 | `fft_status` | FFT status reg |
|
||
| 0x30 | `fft_status_raw` | FFT status raw |
|
||
| 0x38 | `fft_output_fifo` | FFT output FIFO |
|
||
|
||
FPIOA
|
||
-----
|
||
|
||
(source: `lib/drivers/include/fpioa.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `io[48]` | FPIOA GPIO multiplexer io array |
|
||
| 0xc0 | `tie_en[8]` | FPIOA GPIO multiplexer tie enable |
|
||
| 0xe0 | `tie_val[8]` | FPIOA GPIO multiplexer tie value |
|
||
|
||
GPIO
|
||
----
|
||
|
||
(source: `lib/drivers/include/gpio.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `data_output` | Data (output) registers |
|
||
| 0x04 | `direction` | Data direction registers |
|
||
| 0x08 | `source` | Data source registers |
|
||
| 0x10 | `unused_0[9]` | Unused registers, 9x4 bytes |
|
||
| 0x30 | `interrupt_enable` | Interrupt enable/disable registers |
|
||
| 0x34 | `interrupt_mask` | Interrupt mask registers |
|
||
| 0x38 | `interrupt_level` | Interrupt level registers |
|
||
| 0x3c | `interrupt_polarity` | Interrupt polarity registers |
|
||
| 0x40 | `interrupt_status` | Interrupt status registers |
|
||
| 0x44 | `interrupt_status_raw` | Raw interrupt status registers |
|
||
| 0x48 | `interrupt_debounce` | Interrupt debounce registers |
|
||
| 0x4c | `interrupt_clear` | Registers for clearing interrupts |
|
||
| 0x50 | `data_input` | External port (data input) registers |
|
||
| 0x54 | `unused_1[3]` | Unused registers, 3x4 bytes |
|
||
| 0x60 | `sync_level` | Sync level registers |
|
||
| 0x64 | `id_code` | ID code |
|
||
| 0x68 | `interrupt_bothedge` | Interrupt both edge type |
|
||
|
||
GPIOHS
|
||
------
|
||
|
||
(source: `lib/drivers/include/gpiohs.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `input_val` | |
|
||
| 0x04 | `input_en` | |
|
||
| 0x08 | `output_en` | |
|
||
| 0x0c | `output_val` | |
|
||
| 0x10 | `pullup_en` | |
|
||
| 0x14 | `drive` | |
|
||
| 0x18 | `rise_ie` | |
|
||
| 0x1c | `rise_ip` | |
|
||
| 0x20 | `fall_ie` | |
|
||
| 0x24 | `fall_ip` | |
|
||
| 0x28 | `high_ie` | |
|
||
| 0x2c | `high_ip` | |
|
||
| 0x30 | `low_ie` | |
|
||
| 0x34 | `low_ip` | |
|
||
| 0x38 | `iof_en` | |
|
||
| 0x3c | `iof_sel` | |
|
||
| 0x40 | `output_xor` | |
|
||
|
||
I2Cx
|
||
----
|
||
|
||
(source: `lib/drivers/include/i2c.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `con` | I2C Control Register |
|
||
| 0x04 | `tar` | I2C Target Address Register |
|
||
| 0x08 | `sar` | I2C Slave Address Register |
|
||
| 0x0c | `resv1` | reserved |
|
||
| 0x10 | `data_cmd` | I2C Data Buffer and Command Register |
|
||
| 0x14 | `ss_scl_hcnt` | I2C Standard Speed Clock SCL High Count Register |
|
||
| 0x18 | `ss_scl_lcnt` | I2C Standard Speed Clock SCL Low Count Register |
|
||
| 0x1c | `resv2[4]` | reserverd |
|
||
| 0x2c | `intr_stat` | I2C Interrupt Status Register |
|
||
| 0x30 | `intr_mask` | I2C Interrupt Mask Register |
|
||
| 0x34 | `raw_intr_stat` | I2C Raw Interrupt Status Register |
|
||
| 0x38 | `rx_tl` | I2C Receive FIFO Threshold Register |
|
||
| 0x3c | `tx_tl` | I2C Transmit FIFO Threshold Register |
|
||
| 0x40 | `clr_intr` | I2C Clear Combined and Individual Interrupt Register |
|
||
| 0x44 | `clr_rx_under` | I2C Clear RX\_UNDER Interrupt Register |
|
||
| 0x48 | `clr_rx_over` | I2C Clear RX\_OVER Interrupt Register |
|
||
| 0x4c | `clr_tx_over` | I2C Clear TX\_OVER Interrupt Register |
|
||
| 0x50 | `clr_rd_req` | I2C Clear RD\_REQ Interrupt Register |
|
||
| 0x54 | `clr_tx_abrt` | I2C Clear TX\_ABRT Interrupt Register |
|
||
| 0x58 | `clr_rx_done` | I2C Clear RX\_DONE Interrupt Register |
|
||
| 0x5c | `clr_activity` | I2C Clear ACTIVITY Interrupt Register |
|
||
| 0x60 | `clr_stop_det` | I2C Clear STOP\_DET Interrupt Register |
|
||
| 0x64 | `clr_start_det` | I2C Clear START\_DET Interrupt Register |
|
||
| 0x68 | `clr_gen_call` | I2C Clear GEN\_CALL Interrupt Register |
|
||
| 0x6c | `enable` | I2C Enable Register |
|
||
| 0x70 | `status` | I2C Status Register |
|
||
| 0x74 | `txflr` | I2C Transmit FIFO Level Register |
|
||
| 0x78 | `rxflr` | I2C Receive FIFO Level Register |
|
||
| 0x7c | `sda_hold` | I2C SDA Hold Time Length Register |
|
||
| 0x80 | `tx_abrt_source` | I2C Transmit Abort Source Register |
|
||
| 0x84 | `resv3` | reserved |
|
||
| 0x88 | `dma_cr` | I2C DMA Control Register |
|
||
| 0x8c | `dma_tdlr` | I2C DMA Transmit Data Level Register |
|
||
| 0x90 | `dma_rdlr` | I2C DMA Receive Data Level Register |
|
||
| 0x94 | `sda_setup` | I2C SDA Setup Register |
|
||
| 0x98 | `general_call` | I2C ACK General Call Register |
|
||
| 0x9c | `enable_status` | I2C Enable Status Register |
|
||
| 0xa0 | `fs_spklen` | I2C SS, FS or FM+ spike suppression limit |
|
||
| 0xa4 | `resv4[20]` | reserved |
|
||
| 0xf4 | `comp_param_1` | I2C Component Parameter Register 1 |
|
||
| 0xf8 | `comp_version` | I2C Component Version Register |
|
||
| 0xfc | `comp_type` | I2C Component Type Register |
|
||
|
||
This block is replicated for all 3 I2C peripherals.
|
||
|
||
I2Sx
|
||
----
|
||
|
||
(source: `lib/drivers/include/i2s.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x000 | `ier` | I2S Enable Register |
|
||
| 0x004 | `irer` | I2S Receiver Block Enable Register |
|
||
| 0x008 | `iter` | I2S Transmitter Block Enable Register |
|
||
| 0x00c | `cer` | Clock Enable Register |
|
||
| 0x010 | `ccr` | Clock Configuration Register |
|
||
| 0x014 | `rxffr` | Receiver Block FIFO Reset Register |
|
||
| 0x018 | `txffr` | Transmitter Block FIFO Reset Register |
|
||
| 0x01c | `reserved1` | |
|
||
| 0x020 | `channel[4]` | Channel setup (64 bytes per channel) |
|
||
| 0x120 | `reserved2[40]` | |
|
||
| 0x1c0 | `rxdma` | Receiver Block DMA Register |
|
||
| 0x1c4 | `rrxdma` | Reset Receiver Block DMA Register |
|
||
| 0x1c8 | `txdma` | Transmitter Block DMA Register |
|
||
| 0x1cc | `rtxdma` | Reset Transmitter Block DMA Register |
|
||
| 0x1d0 | `reserved3[8]` | reserved |
|
||
| 0x1f0 | `i2s_comp_param_2` | Component Parameter Register 2 |
|
||
| 0x1f4 | `i2s_comp_param_1` | Component Parameter Register 1 |
|
||
| 0x1f8 | `i2s_comp_version_1`| I2S Component Version Register |
|
||
| 0x1fc | `i2s_comp_type` | I2S Component Type Register |
|
||
|
||
This block is replicated for all 3 I2S peripherals.
|
||
|
||
KPU
|
||
---
|
||
|
||
(source: `lib/drivers/include/kpu.h`)
|
||
|
||
Registers are 64-bit.
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `layer_argument_fifo` | |
|
||
| 0x08 | `interrupt_status` | |
|
||
| 0x10 | `interrupt_raw` | |
|
||
| 0x18 | `interrupt_mask` | |
|
||
| 0x20 | `interrupt_clear` | |
|
||
| 0x28 | `fifo_threshold` | |
|
||
| 0x30 | `fifo_data_out` | |
|
||
| 0x38 | `fifo_ctrl` | |
|
||
| 0x40 | `eight_bit_mode` | Enable 8-bit instead of 16-bit precision |
|
||
|
||
OTP
|
||
---
|
||
|
||
(seems undocumented, and only used from ROM)
|
||
|
||
```
|
||
0x68 104 r fuses A?
|
||
0xb8 184 r fuses B1?
|
||
0xbc 188 r fuses B0?
|
||
```
|
||
|
||
The fuse bits determine some choices during the ROM boot process, such as from what flash to boot,
|
||
whether to decrypt flash before boot, and so on.
|
||
|
||
There is also a 128 kbit one-time programmable memory that can be read (and
|
||
written) through this interface, and it can be prompted to provide a AES128 key to
|
||
the AES peripheral without exposing it to software.
|
||
|
||
PLIC
|
||
----
|
||
|
||
(source: `lib/drivers/include/plic.h`, addresses are absolute)
|
||
|
||
| Address | Description |
|
||
| ---------- | ------------------------------- |
|
||
| 0x0c000000 | Reserved |
|
||
| 0x0c000004 | source 1 priority |
|
||
| 0x0c000008 | source 2 priority |
|
||
| ... | ... |
|
||
| 0x0c000ffC | source 1023 priority |
|
||
| | |
|
||
| 0x0c001000 | Start of pending array |
|
||
| ... | (read-only) |
|
||
| 0x0c00107c | End of pending array |
|
||
| 0x0c001080 | Reserved |
|
||
| ... | ... |
|
||
| 0x0c001fff | Reserved |
|
||
| | |
|
||
| 0x0c002000 | target 0 enables |
|
||
| 0x0c002080 | target 1 enables |
|
||
| ... | ... |
|
||
| 0x0c1f1f80 | target 15871 enables |
|
||
| 0x0c1f2000 | Reserved |
|
||
| ... | ... |
|
||
| 0x0c1ffffc | Reserved |
|
||
| | |
|
||
| 0x0c200000 | target 0 priority threshold |
|
||
| 0x0c200004 | target 0 claim/complete |
|
||
| ... | ... |
|
||
| 0x0c201000 | target 1 priority threshold |
|
||
| 0x0c201004 | target 1 claim/complete |
|
||
| ... | ... |
|
||
| 0x0ffff000 | target 15871 priority threshold |
|
||
| 0x0ffff004 | target 15871 claim/complete |
|
||
|
||
This looks similar to, or even the same as, the SiFive PLIC.
|
||
|
||
RTC
|
||
---
|
||
|
||
(source: `lib/drivers/include/rtc.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `date` | Timer date information |
|
||
| 0x04 | `time` | Timer time information |
|
||
| 0x08 | `alarm_date` | Alarm date information |
|
||
| 0x0c | `alarm_time` | Alarm time information |
|
||
| 0x10 | `initial_count` | Timer counter initial value |
|
||
| 0x14 | `current_count` | Timer counter current value |
|
||
| 0x18 | `interrupt_ctrl` | RTC interrupt settings |
|
||
| 0x1c | `register_ctrl` | RTC register settings |
|
||
| 0x20 | `reserved0` | Reserved |
|
||
| 0x24 | `reserved1` | Reserved |
|
||
| 0x28 | `extended` | Timer extended information |
|
||
|
||
SHA256
|
||
------
|
||
|
||
(source: `lib/drivers/include/sha256.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `sha_result[8]` | Calculated SHA256 return value |
|
||
| 0x20 | `sha_data_in1` | SHA256 input data from this register |
|
||
| 0x24 | `reserved0` | |
|
||
| 0x28 | `sha_num_reg` | |
|
||
| 0x2c | `sha_function_reg_0` | |
|
||
| 0x30 | `reserved1` | |
|
||
| 0x34 | `sha_function_reg_1` | |
|
||
|
||
SPIx
|
||
----
|
||
|
||
(source: `lib/drivers/include/spi.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x000 | `ctrlr0` | SPI Control Register 0 |
|
||
| 0x004 | `ctrlr1` | SPI Control Register 1 |
|
||
| 0x008 | `ssienr` | SPI Enable Register |
|
||
| 0x00c | `mwcr` | SPI Microwire Control Register |
|
||
| 0x010 | `ser` | SPI Slave Enable Register |
|
||
| 0x014 | `baudr` | SPI Baud Rate Select |
|
||
| 0x018 | `txftlr` | SPI Transmit FIFO Threshold Level |
|
||
| 0x01c | `rxftlr` | SPI Receive FIFO Threshold Level |
|
||
| 0x020 | `txflr` | SPI Transmit FIFO Level Register |
|
||
| 0x024 | `rxflr` | SPI Receive FIFO Level Register |
|
||
| 0x028 | `sr` | SPI Status Register |
|
||
| 0x02c | `imr` | SPI Interrupt Mask Register |
|
||
| 0x030 | `isr` | SPI Interrupt Status Register |
|
||
| 0x034 | `risr` | SPI Raw Interrupt Status Register |
|
||
| 0x038 | `txoicr` | SPI Transmit FIFO Overflow Interrupt Clear Register |
|
||
| 0x03c | `rxoicr` | SPI Receive FIFO Overflow Interrupt Clear Register |
|
||
| 0x040 | `rxuicr` | SPI Receive FIFO Underflow Interrupt Clear Register |
|
||
| 0x044 | `msticr` | SPI Multi-Master Interrupt Clear Register |
|
||
| 0x048 | `icr` | SPI Interrupt Clear Register |
|
||
| 0x04c | `dmacr` | SPI DMA Control Register |
|
||
| 0x050 | `dmatdlr` | SPI DMA Transmit Data Level |
|
||
| 0x054 | `dmardlr` | SPI DMA Receive Data Level |
|
||
| 0x058 | `idr` | SPI Identification Register |
|
||
| 0x05c | `ssic_version_id` | SPI DWC\_ssi component version |
|
||
| 0x060 | `dr[36]` | SPI Data Register 0-36 |
|
||
| 0x0f0 | `rx_sample_delay` | SPI RX Sample Delay Register |
|
||
| 0x0f4 | `spi_ctrlr0` | SPI SPI Control Register |
|
||
| 0x0f8 | `resv` | |
|
||
| 0x0fc | `xip_mode_bits` | SPI XIP Mode bits |
|
||
| 0x100 | `xip_incr_inst` | SPI XIP INCR transfer opcode |
|
||
| 0x104 | `xip_wrap_inst` | SPI XIP WRAP transfer opcode |
|
||
| 0x108 | `xip_ctrl` | SPI XIP Control Register |
|
||
| 0x10c | `xip_ser` | SPI XIP Slave Enable Register |
|
||
| 0x110 | `xrxoicr` | SPI XIP Receive FIFO Overflow Interrupt Clear Register |
|
||
| 0x114 | `xip_cnt_time_out` | SPI XIP time out register for continuous transfers |
|
||
| 0x118 | `endian` | SPI Endian |
|
||
|
||
This block is replicated for all 4 SPI peripherals except for SPI2, which is SPI
|
||
slave-only and has a slightly different interface.
|
||
|
||
SYSCTL
|
||
------
|
||
|
||
(source: `lib/drivers/include/sysctl.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | -------------- | ----------------------------------- |
|
||
| 0x00 | `git_id` | Git short commit id |
|
||
| 0x04 | `clk_freq` | System clock base frequency |
|
||
| 0x08 | `pll0` | PLL0 controller |
|
||
| 0x0c | `pll1` | PLL1 controller |
|
||
| 0x10 | `pll2` | PLL2 controller |
|
||
| 0x14 | `resv5` | Reserved |
|
||
| 0x18 | `pll_lock` | PLL lock tester |
|
||
| 0x1c | `rom_error` | AXI ROM detector |
|
||
| 0x20 | `clk_sel0` | Clock select controller0 |
|
||
| 0x24 | `clk_sel1` | Clock select controller1 |
|
||
| 0x28 | `clk_en_cent` | Central clock enable |
|
||
| 0x2c | `clk_en_peri` | Peripheral clock enable |
|
||
| 0x30 | `soft_reset` | Soft reset ctrl |
|
||
| 0x34 | `peri_reset` | Peripheral reset controller |
|
||
| 0x38 | `clk_th0` | Clock threshold controller 0 |
|
||
| 0x3c | `clk_th1` | Clock threshold controller 1 |
|
||
| 0x40 | `clk_th2` | Clock threshold controller 2 |
|
||
| 0x44 | `clk_th3` | Clock threshold controller 3 |
|
||
| 0x48 | `clk_th4` | Clock threshold controller 4 |
|
||
| 0x4c | `clk_th5` | Clock threshold controller 5 |
|
||
| 0x50 | `clk_th6` | Clock threshold controller 6 |
|
||
| 0x54 | `misc` | Miscellaneous controller |
|
||
| 0x58 | `peri` | Peripheral controller |
|
||
| 0x5c | `spi_sleep` | SPI sleep controller |
|
||
| 0x60 | `reset_status` | Reset source status |
|
||
| 0x64 | `dma_sel0` | DMA handshake selector |
|
||
| 0x68 | `dma_sel1` | DMA handshake selector |
|
||
| 0x6c | `power_sel` | IO Power Mode Select controller |
|
||
| 0x70 | `resv28` | Reserved |
|
||
| 0x74 | `resv29` | Reserved |
|
||
| 0x78 | `resv30` | Reserved |
|
||
| 0x7c | `resv31` | Reserved |
|
||
|
||
TIMERx
|
||
------
|
||
|
||
(source: `lib/drivers/include/timer.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `channel[4]` | TIMER\_N Register (20 bytes per channel) |
|
||
| 0x50 | `resv1[20]` | |
|
||
| 0xa0 | `intr_stat` | TIMER Interrupt Status Register |
|
||
| 0xa4 | `eoi` | TIMER Interrupt Clear Register |
|
||
| 0xa8 | `raw_intr_stat` | TIMER Raw Interrupt Status Register |
|
||
| 0xac | `comp_version` | TIMER Component Version Register |
|
||
| 0xb0 | `load_count2[4]` | TIMER\_N Load Count2 Register |
|
||
|
||
UARTx
|
||
-----
|
||
|
||
(source: `lib/drivers/include/uart.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `RBR` | Receive Buffer Register - lower 8 bits (read) |
|
||
| 0x00 | `DLL` | Divisor Latch LSB |
|
||
| 0x00 | `THR` | Transmitter Holding Register - lower 8 bits (write) |
|
||
| 0x04 | `DLH` | Divisor latch MSB |
|
||
| 0x04 | `IER` | Interrupt Enable Register |
|
||
| 0x08 | `FCR` | FIFO Control Register |
|
||
| 0x08 | `IIR` | Interrupt Identification Register |
|
||
| 0x0c | `LCR` | Line Control Register |
|
||
| 0x10 | `MCR` | Modem Control Register |
|
||
| 0x14 | `LSR` | Line Status Register |
|
||
| 0x18 | `MSR` | Modem Status Register |
|
||
| 0x1c | `SCR` | Scratch |
|
||
| 0x20 | `LPDLL` | Low Power Divisor Latch (Low) Register |
|
||
| 0x24 | `LPDLH` | Low Power Divisor Latch (High) Register |
|
||
| 0x28 | `reserved1[2]` | |
|
||
| 0x30 | `SRBR[16]` | Shadow Receive Buffer Register |
|
||
| 0x30 | `STHR[16]` | Shadow Transmit Holding Register |
|
||
| 0x70 | `FAR` | FIFO Access Register |
|
||
| 0x74 | `TFR` | Transmit FIFO Read Register |
|
||
| 0x78 | `RFW` | Receive FIFO Write Register |
|
||
| 0x7c | `USR` | UART Status Register |
|
||
| 0x80 | `TFL` | Transmit FIFO Level |
|
||
| 0x84 | `RFL` | Receive FIFO Level |
|
||
| 0x88 | `SRR` | Software Reset Register |
|
||
| 0x8c | `SRTS` | Shadow Request to Send Register |
|
||
| 0x90 | `SBCR` | Shadow Break Control Register |
|
||
| 0x94 | `SDMAM` | Shadow DMA Mode |
|
||
| 0x98 | `SFE` | Shadow FIFO Enable |
|
||
| 0x9c | `SRT` | Shadow RCVR Trigger Register |
|
||
| 0xa0 | `STET` | Shadow TX Empty Trigger Register |
|
||
| 0xa4 | `HTX` | Halt TX Regster |
|
||
| 0xa8 | `DMASA` | DMA Software Acknowledge Register |
|
||
| 0xac | `TCR` | Transfer Control Register |
|
||
| 0xb0 | `DE_EN` | DE Enable Register |
|
||
| 0xb4 | `RE_EN` | RE Enable Register |
|
||
| 0xb8 | `DET` | DE Assertion Time Register |
|
||
| 0xbc | `TAT` | Turn-Around Time Register |
|
||
| 0xc0 | `DLF` | Divisor Latch (Fractional) Register |
|
||
| 0xc4 | `RAR` | Receive-Mode Address Register |
|
||
| 0xc8 | `TAR` | Transmit-Mode Address Register |
|
||
| 0xcc | `LCR_EXT` | Line Control Register (Extended) |
|
||
| 0xd0 | `reserved2[9]` | |
|
||
| 0xf4 | `CPR` | Component Parameter Register |
|
||
| 0xf8 | `UCV` | UART Component Version |
|
||
| 0xfc | `CTR` | Component Type Register |
|
||
|
||
This block is replicated for all 3 UART peripherals. The latter registers (0x20
|
||
and higher) are not used in the SDK, but defined in the structure. Their use is
|
||
unknown, although the names match some other UART controllers.
|
||
The best match to the register names and offsets appears to be the UART described in
|
||
[HUGEIC Communication Interface Peripheral User’s Guide](http://www.huge-ic.com/Communication%20Interface%20Peripheral%20User%27s%20Guide%20V0.1.pdf).
|
||
|
||
UARTHS
|
||
------
|
||
|
||
(source: `lib/drivers/include/uarths.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | -------- | ------------------------------- |
|
||
| 0x000 | `txdata` | Transmit data register |
|
||
| 0x004 | `rxdata` | Receive data register |
|
||
| 0x008 | `txctrl` | Transmit control register |
|
||
| 0x00c | `rxctrl` | Receive control register |
|
||
| 0x010 | `ie` | UART interrupt enable |
|
||
| 0x014 | `ip` | UART Interrupt pending |
|
||
| 0x018 | `div` | Baud rate divisor |
|
||
|
||
WDTx
|
||
----
|
||
|
||
(source: `lib/drivers/include/wdt.h`)
|
||
|
||
| Ofs | Name | Description |
|
||
| ----- | ----------------- | ------------------------------------------------------------- |
|
||
| 0x00 | `cr` | WDT Control Register |
|
||
| 0x04 | `torr` | WDT Timeout Range Register |
|
||
| 0x08 | `ccvr` | WDT Current Counter Value Register |
|
||
| 0x0c | `crr` | WDT Counter Restart Register |
|
||
| 0x10 | `stat` | WDT Interrupt Status Register |
|
||
| 0x14 | `eoi` | WDT Interrupt Clear Register |
|
||
| 0x18 | `resv1` | |
|
||
| 0x1c | `prot_level` | WDT Protection level Register |
|
||
| 0x20 | `resv4[49]` | |
|
||
| 0xe4 | `comp_param_5` | WDT Component Parameters Register 5 |
|
||
| 0xe8 | `comp_param_4` | WDT Component Parameters Register 4 |
|
||
| 0xec | `comp_param_3` | WDT Component Parameters Register 3 |
|
||
| 0xf0 | `comp_param_2` | WDT Component Parameters Register 2 |
|
||
| 0xf4 | `comp_param_1` | WDT Component Parameters Register 1 |
|
||
| 0xf8 | `comp_version` | WDT Component Version Register |
|
||
| 0xfc | `comp_type` | WDT Component Type Register |
|
||
|
||
This block is replicated for all 2 WDT peripherals.
|