increment/decrement (C-a/C-x) had some buggy behavior where selections
could be offset incorrectly or the editor could panic with some edits
that changed the number of characters in a number or date. These stemmed
from the automatic jumping behavior which attempted to find the next
date or integer to increment. The jumping behavior also complicated the
code quite a bit and made the behavior somewhat difficult to predict
when using many cursors.
This change removes the automatic jumping behavior and only increments
or decrements when the full text in a range of a selection is a number
or date. This simplifies the code and fixes the panics and buggy
behaviors from changing the number of characters.
After changes in #5239, the loaded configuration wasn't stored,
resulting in a success message even if the instance kept the previous
configuration values.
Commit 1b89d3e535 introduced a regression
where opening a new file would no longer work, because attempting to
canonicalize its path would lead to a "No such file or directory"
error. Fall back to opening a new file when encountering an error to
fix this case.
This commit addresses issue 5193, where the author
requested that the name of the binary needed is printed along
with the rest of the health information.
This commit adds a format! macro which formats in the name of the
binary and then it will be printed along with the rest of the
debug information. The value in cmd is referenced to the call
to which, and then consumed upon the call to format!
This roughly matches the behavior of the diagnostic picker: when
jumping to a diagnostic with `[d`/`]d`/`[D`/`]D`, the range of the
diagnostic is selected instead of the start point.
A language server might send None as the response to workspace symbols.
We should treat this as the empty Vec rather than the server sending
an error status. This fixes the interaction with gopls which uses
None to mean no matching symbols.
If the new results shown by the picker select a file that hasn't been
previewed before, the idle timeout would not trigger highlighting on
that file. With this change, we reset the idle timeout and allow that
file to be highlighted on the next idle timeout event.
This change uses the idle-timeout event to trigger fetching new results
in the DynamicPicker, so idle-timeout becomes a sort of debounce. This
prevents querying the language server overly aggressively.
Most language servers limit the number of workspace symbols that
are returned with an empty query even though all symbols are
supposed to be returned, according to the spec (for perfomance
reasons). This patch adds a workspace symbol picker based on a
dynamic picker that allows re-requesting the symbols on every
keypress (i.e. when the picker query text changes). The old behavior
has been completely replaced, and I have only tested with
rust-analyzer so far.
The error messages for a theme that failed to be deserialized (or
otherwise failed to load) were covered up by the context/with_context
calls:
* The log message for a bad theme configured in config.toml would only
say "Failed to deserilaize theme"
* Selecting a bad theme via :theme would show "Theme does not exist"
With these changes, we let the TOML deserializer errors bubble up, so
the error messages can now say the line number of a duplicated
key - and that key's name - when a theme fails to load because of a
duplicated key.
Providing a theme which does not exist to :theme still gives a helpful
error message: "No such file or directory."
* Reset mode when changing buffers
This is similar to the change in
e4c9d4082a: reset the editor to normal
mode when changing buffers. Usually the editor is already in normal
mode but it's possible to setup insert-mode keybindings that change
buffers.
* Move normal mode entering code to Editor
This should be called internally in the Editor when changing documents
(Editor::switch) or changing focuses (Editor::focus).
* add command and keybding to jump to next/prev hunk
* add textobject for change
* Update helix-vcs/src/diff.rs
Co-authored-by: Michael Davis <mcarsondavis@gmail.com>
* select entire hunk instead of first char
* fix selection range
Co-authored-by: Michael Davis <mcarsondavis@gmail.com>
* Add `View::ensure_cursor_in_view_center` to adjust view after searching and jumping
Also `offset_coodrs_to_in_view` was refactored to reduce duplicated position calculations.
* Fix a wrong offset calculation in `offset_coords_to_in_view_center`
It ignored `scrolloff` if `centering` is false.
Completion edits - either basic `insert_text` strings or structured
`text_edit`s - are assumed by the LSP spec to apply to the current
cursor (or at least the trigger point). We can use the range (if any)
and text given by the Language Server to create a transaction that
changes all ranges in the current selection though, allowing auto-
complete to affect multiple cursors.
